This paper presents a systematic comparison of the relationship between transmission line characteristic impedance and Q-factor of CPW, slow-wave CPW, microstrip, and slow-wave microstrip in the same CMOS back-end-of-line process. It is found that the characteristic impedance for optimal Q-factor depends on the ground-to-ground spacing of the slow-wave transmission line. Although the media are sho

In this article, a meander line-shaped pentaband (2.18?2.24, 2.38?2.46, 2.65?2.70, 3.10?3.32, 3.38?3.46 GHz) four-element multiple-input?multiple-output antenna is presented. The proposed antenna is also circularly polarized in two bands (at 2.2 and 2.4 GHz) with dual-polarization like right-handed at port 1 or 3 and left-handed at port 2 or 4, which is widely used for mobile satellite services (M

An analysis about the backscattering characteristics of a metamaterial coated magnetodielectric sphere covered with a metasurface has been presented. The effects of various types of metamaterial coatings and surface reactances of lossless metasurface upon the backscattering cross-section of a metamaterial coated magnetodielectric sphere covered with a metasurface have been studied. It is shown tha

In this paper, a coplanar waveguide-fed ultra-wideband-multiple-input and multiple-output (UWB-MIMO) antenna with a novel stub for isolation has been presented. The dimensions of the proposed antenna are 18 × 22 × 1.6 mm. The proposed antenna is design on an FR4 substrate and simulated in CST studio. The || of the presented MIMO antenna is less than ?10 dB between 2.8 and 13 GHz with an impedance

We present a tunable planar groove gap waveguide (PGGWG) resonant cavity at K-band. The cavity demonstrates varactor loading and biasing without bridging wires or annular rings, as commonly is required in conventional substrate-integrated waveguide (SIW) resonant cavities. A detailed co-simulation strategy is also presented, with indicative parametric tuning data. Measured results indicate a 4.48%

Semiconductor deposition on magnetron's cathode surface using different materials such as gallium nitride (GaN) and silicon carbide (SiC) semiconductors is conducted to grow approximately 80, 100 and 120 nm plasma layers. The cathode is then used to generate high frequency and low-power microwave for further comparison and analysis with the conventional magnetron operation. Parameter of analysis t

In this paper, we describe the design, layout, and performance of a 6-bit TTD (true time delay) chip operating over the entire band of 2?18 GHz. The 1.15 mm chip is implemented using TSMC foundry 65 nm technology. The least significant bit is 1 ps. The design is based on the concept of all-pass network with some modifications intended to reduce the number of unit cells. Thus, the first three bits

A suspended-stripline Gysel low-insertion-loss power combiner is presented in this paper. The multi-layer cavity structure reduces the circuit size and increases power density, composed of suspended strip lines and coaxial lines. The transmission-line theory is used to analyze this proposed power combiner, and the equivalent circuit model is developed to investigate the characteristics and design

Current designs of space IMUX filters are based on dual-mode circular waveguide cavities, on dielectric resonators or, at the lower end of the frequency spectrum, on coaxial resonators. This paper presents a new kind of IMUX filter aimed at high operating frequencies (Ka, Q, and V bands) which was developed in the frame of an ESA funded study named KALOS-DEVAQ. The new filter implements a quasi-el

Modern space communication systems often need high-power low-frequency (UHF, L-, S-, and C-band) low-pass filters (LPFs) with wide stopbands extending to Ka-band and beyond. Current design approaches frequently fail to meet these requirements completely. This paper proposes a new coaxial LPF concept and design methodology. The LPF consists of an array of cavity elements, which operate with transve

The manuscript reports on additively-manufactured (AM) coaxial-resonator-based bandpass filters (BPFs) and RF diplexers. A monolithic integration concept using stereolithography apparatus (SLA) is proposed and discussed in detail. Coupled-resonator-based synthesis alongside full-electromagnetic-based design methods is used for the design of the monolithic filters and RF diplexers. In particular, t

A common strategy to reduce the cost of a filter is to use a manufacturing technique with an intermediate accuracy and use tuning elements to compensate for the manufacturing errors. However, including tuning elements in the final EM simulations, and tuning the filters after manufacturing, can be quite challenging. In this context, therefore, we review in this paper two powerful filter design proc

The design and first experimental results of Tx and Rx L-band bandpass filters for a high-power satellite diplexer are presented in this paper. Designed in the framework of an ESA ARTES AT project, the filters are based on TM mode dielectric resonators. These resonators allow for better results in terms of volume occupation with respect to other dielectric resonators still maintaining high Q-facto

In this paper, the influence of the cutting plane as well as the orientation of the cavities in cross-coupled W-band waveguide filters are investigated. When waveguide filters are manufactured with the commonly known CNC (computer numerical control) milling technique, at least one cutting plane is required. The position of this cutting plane has an impact on the composition of the cavities, the ma

This paper presents a review of the recent advances in the field of substrate integrated waveguide (SIW) filters, with particular emphasis on the techniques adopted to increase the out-of-band rejection of the filters and on the miniaturization strategies. After an overview of classical approaches to introduce transmission zeros in SIW filters, a number of recently introduced techniques are presen

This paper describes the outcome of the ?Small user TErminal multi band DIplexer? project where the goal is the validation of novel SMD-compliant planar diplexer. The real application scenario concerns an integrated multi-band radio terminal for ground-segment satellite links. The advantageous and novel approach involves the simultaneous use of three different well-established concepts: a microstr

The novel acoustic transversal topology has demonstrated to be a potential candidate for the development of the next generation of communication filters. The major asset of this topology is its capacity to achieve any filter response without the detriment of limited electro-acoustic coupling. Additionally, this topology prompts for an easy connection of different filters to create multiband and mu

A class of multi-band planar diplexer with sub-sets of frequency-contiguous transmission bands is reported. Such a radio frequency (RF) device is suitable for lightweight high-frequency receivers aimed at multi-band/multi-purpose mobile satellite communications systems. It consists of two channelizing filters, each of them being made up of the in-series cascade connection of replicas of a constitu

A continuously tunable Ku-band waveguide diplexer is proposed in this paper. This diplexer is based on a hybrid coupler topology and is composed of an input filter centered at 11.9 GHz with a 200 MHz bandwidth, a pair of ladder-type hybrid couplers, and a pair of tunable filters. This diplexer can provide two bandpass channels (channels 1 and 2) that can continuously go from a state where the band

This paper aims to present some outcomes from a European Space Agency (ESA) Technology Research Programme (TRP) project on R&D of new design techniques, concepts, and filtering configurations for tunable IF (intermediate frequency) filters with a compact footprint, wide bandwidth tuning range (covering from 49 to 478 MHz at = 1 GHz) as well as equivalent high- performance (i.e. low insertion loss

In this paper, a general method for synthesizing dispersive coupling matrix (DCM) of coupled-resonator bandpass filters with the general dispersion is proposed. Compared to the dispersion-less coupling matrix synthesized by classic approaches, the DCM incorporates the identity of the physical realization and provides an accurate description of the filter. Moreover, the DCM can accurately describe

In this paper, a modular waveguide filter platform suitable for educational and prototyping purposes is presented. The waveguide filter platform is dimensioned to work in the F-band (4.9?7.05 GHz). The design of the platform is discussed and versatile application possibilities are shown in many examples. The platform can be used to realize generalized Chebyshev filters with or without cross-coupli